At present, most offices use partition doors, so the use of glass partition doors is gradually increasing, and the natural sales volume is also increasing. But many people are curious and want to know glass partition door, glass sliding door, glass high compartment Installation methods of various glass doors and some precautions during installation. Let's talk about the installation methods and precautions of various glass doors for you!

濟南玻璃門擺設門徑：

Jinan glass door decoration door diameter:

1、 定位、放線：由靜止玻璃與勾當玻璃門扇組合玻璃門，差異進行放線定位，遵循整治和施工圖紙需求，放出玻璃門的定位線，一起鑒定門框方位。

1. Positioning and setting out: set out and locate the glass door by combining the static glass and the active glass door leaf. Set out the positioning line of the glass door and identify the orientation of the door frame together in accordance with the requirements of the rectification and construction drawings.

2、 擺設框頂部限位槽：限位槽的寬應大于玻璃厚度二四毫米,槽深為十二十毫米。裝置時，一***由所彈中凡線引出兩條金屬裝修板邊線，接著按邊線進行門框頂部限位槽的擺設，經由膠合墊板斡旋槽口內的槽深。

2. Limit groove at the top of the display frame: the width of the limit groove shall be 2-4 mm greater than the glass thickness, and the groove depth shall be 10-20 mm. When installing the device, one first leads out two metal decoration board sidelines from the middle line, then arranges the limit groove at the top of the door frame according to the sideline, and mediates the groove depth in the groove through the glued base plate.

3、 裝置金屬飾面的木底托：把方木固定在地上上，用***膠把金屬飾面板粘在木上。若選用鋁合金方管，興許用鋁角固定在框柱上，或用木螺釘固定在埋入地上中的木磚上。

3. Wooden bottom support with metal finish: fix the square wood on the ground, and stick the metal decorative panel to the wood with universal glue. If aluminum alloy square pipe is selected, it may be fixed on the frame column with aluminum angle or on the wooden brick embedded in the ground with wood screws.

4、 裝置豎向門框：接所彈外圍線釘立門框方木，接著用膠合板斷定門框柱的狀態和方位，終外包金屬裝修面。包飾面時要把飾面仇敵接縫方位放在裝置玻璃的中間中門方位。

4. Installation of vertical door frame: connect the snapped peripheral line to nail the square wood of the door frame, then determine the state and orientation of the door frame column with plywood, and finally wrap the metal decoration surface. When wrapping the veneer, the joint direction of the veneer shall be placed in the middle door direction of the device glass.

5、 裝置玻璃：用玻璃吸盤機把厚玻璃吸緊，把厚玻璃板抬起移擺設方位。先把玻璃上部刺進門框頂部的限位槽，再把把玻璃的下部放終于托上。

5. Glass installation: use the glass suction cup machine to suck the thick glass tightly, lift the thick glass plate and move it to the layout direction. Stab the upper part of the glass into the limit slot at the top of the door frame, and then put the lower part of the glass on the support.

6、 靜止玻璃：在底托方木上的表里釘兩根小方木條把厚玻璃夾在中門，在方木條上涂刷全能膠并把飾面金屬粘在在方木條上。

6. Static glass: nail two small square wood strips on the surface and inside of the square wood on the bottom support, clamp the thick glass on the middle door, brush all-round glue on the square wood strip, and stick the facing metal on the square wood strip.

7、 注玻璃膠封口：在頂部限位槽與底部托槽口的兩頭，以及厚玻璃與框柱的對縫處等各縫隙處，寫入玻璃膠封口，用工具刮去殘余的玻璃膠。

7. Note: glass glue sealing: write glass glue sealing at the two ends of the top limit groove and the bottom bracket mouth, as well as the butt joint between thick glass and frame column, and scrape off the residual glass glue with tools.

8、 玻璃對接：玻璃門靜止有些因尺寸過大而需要拼接時，其對縫要有二三毫米的寬度，玻璃板邊要發展倒角措置。

8. Glass butt joint: when the glass door is still and needs to be spliced due to its large size, the butt joint should have a width of 2-3mm, and the edge of the glass plate should be chamfered.

9、 地彈簧擺設：門扇裝置前地上地彈簧與門框頂面的定位銷應裝置結束何況有重要同軸線，擺設時***用吊垂線檢查確保在同不絕線上。

9. Floor spring arrangement: the floor spring in front of the door leaf device and the locating pin on the top surface of the door frame should be installed at the end. In addition, there is an important coaxial line. During the arrangement, it is best to check with a hanging vertical line to ensure that it is on the same continuous line.

10、 擺設凹凸門夾：把凹凸金屬門夾離別裝在玻璃門扇上下中間，假設門扇高度缺乏，可鄙人門夾內玻璃底部墊木夾板條。

10. Furnishing concave convex door clamp: install concave convex metal door clamp separately in the upper and lower middle of glass door leaf. Assuming that the door leaf is lack of height, the bottom of glass in the door clamp is padded with wooden splint strip.

11、 固定玻璃門門夾：定好門扇高度后，在玻璃與凹凸門夾內的中間縫隙刺進小木條，在縫隙中寫入玻璃膠固定。

11. Fixing the glass door clip: after setting the height of the door leaf, stab a small wooden strip into the middle gap between the glass and the concave convex door clip, and write glass glue in the gap for fixing.

12、 門扇擺設：先把定位銷用自己的療養螺釘調出橫梁立體二毫米，把單元玻璃門扇豎起來，門扇下門夾內的轉動銷聯接件的孔位對準地彈簧的動彈銷軸，轉動門扇把孔位套入 銷軸上，把門扇遷移轉變與門框橫梁成直角，把門扇上門夾中的轉折聯接件孔對準門框橫梁上的定位銷，調節定位銷的調治螺釘，把定位銷刺進孔內。

12. Door leaf decoration: first, pull out the positioning pin with its own convalescent screw to the three-dimensional 2mm of the cross beam, erect the unit glass door leaf, align the hole position of the rotating pin connector in the door clamp under the door leaf with the dynamic pin shaft of the ground spring, rotate the door leaf, put the hole position on the pin shaft, and move the door leaf to form a right angle with the cross beam of the door frame, Align the turning connector hole in the door clamp of the door leaf with the locating pin on the door frame beam, adjust the adjusting screw of the locating pin, and pierce the locating pin into the hole.

13、 拉手?jǐn)[設：擺設前在拉咭片進玻璃的有些涂少量玻璃膠，拉手裝配時根部與玻璃靠緊密后再按緊靜止螺釘，以確保拉手沒有松動征兆。

13. Handle arrangement: before the arrangement, apply a small amount of glass glue to some of the parts that pull the card into the glass. When the handle is assembled, the root is close to the glass, and then press the static screw to ensure that the handle is not loose.

濟南玻璃門裝置留意變亂：

Attention to the accident of Jinan glass door device:

1、裝置玻璃門前，要檢查門窗扇是不是平整，預留孔眼是否是徹底、粗略，要是不適宜需求的就應當先校訂。

1. Before installing the glass door, check whether the door and window leaves are flat and whether the reserved holes are thorough and rough. If they are not suitable for the needs, they should be revised first.

2、裝置鋼框、門扇玻璃應用鋼絲卡固定，隔斷不得大于300妹妹，且每邊許多于兩個，也也許以在鋼絲卡上抹油灰面層，以增加密封性。

2. The steel frame and door leaf glass of the device shall be fixed with steel wire clamp, and the partition shall not be greater than 300 meters, and there are more than two on each side, or the putty surface layer may be applied on the steel wire clamp to increase the tightness.

3、如用油灰固定，則油灰應填實抹光。如用橡皮墊，應先將橡皮墊嵌入，并用壓條與螺釘靜止。

3. If it is fixed with putty, the putty shall be filled and troweled. If a rubber pad is used, the rubber pad shall be embedded first, and the pressure strip and screw shall be used to stand still.

4、如選用壓條靜止，通常在四邊或兩端加壓條，用密封膠封好。

4. If the pressure strip is selected to be static, the pressure strip is usually added on four sides or both ends and sealed with sealant.

5、裝置種種募捐質料要合適企圖需乞降有關尺度規定。

5. The installation of various fund-raising materials should be appropriate, and the relevant standards and regulations need to be lowered.

6、組裝彩色玻璃、區花玻璃時，應與籌畫丹青相符，不得錯位、斜曲和松動，玻璃的朝向應相宜規畫需求。

6. When assembling colored glass and area patterned glass, it shall be consistent with the planned Danqing, and shall not be misplaced, skewed and loose. The orientation of the glass shall meet the planning requirements.

以上是由濟南凱達玻璃為大家整理出來的一些玻璃門安裝方法和安裝時的注意事項，希望通過以上內容的分析和了解能夠真正幫到你。

The above are some installation methods and precautions for glass doors sorted out by Jinan Kaida glass. I hope the analysis and understanding of the above contents can really help you.